Program Rendering Chip Overview
Since the Pokemon Mini does not drive a conventional display, it does not operate like typical display driver. The PRC was created as a method for driving a serial LCD display. It's entire purpose is to blit images from various locations in memory to an internal frame buffer, and then force it out to GDRAM in on the LCD Controller. This is all done transparently.
The PRC operates by monitering a display counter, which overflows aproximately 66 times a second. When the counter reaches specific values, the PRC triggers various components. It can operates in 3 stages, Map render, Sprite Render and Frame Copy. The values which the counters trigger on have not been determined.
During these various stages, the CPU is halted, and yields the bus to the PRC. Depending on the enabled stages, the PRC will read various locations from memory (cartridge and ram) and build a frame buffer to $1000 ~ $12FF. Depending on the complexity of the scene, and the enabled modes, developers lose varying amounts of processor time.
Since all three display stages can be enabled or disabled independantly, users can perform a number of tricks such as multiplexing sprites (by disabling frame copy on even frames, and map copy on odd frames, changing the sprites each time), running in a pure frame-buffered mode, or simply use the LCD controller manually by disabling the VPU all together.
The PRC shares ram with the CPU, so the more modes that are enabled, the less ram is usable by the developer.
Map Rendering Stage
Stage 1 of the PRC is a map renderer. This stage can render a variable size 8x8 tile based map to the frame buffer (located at $1000). This mode operates by using a 24bit address (PRC_MAP_*) as the base for the tile set, and a tile map located at $1360. This stage is enabled by using bit 2 of PRC_MODE.
|0||12 x 16|
|1||16 x 12|
|2||24 x 8|
|3||24 x 16|
Tile maps are arranged in left to right order, wrapping around to the next line.
The value in the tile map then points to an 8 byte tile. The location of the tile is specified by (Tile * 8 + PRC_MAP_*). The tiles are encoded in vertical strips, each 8 pixel strip = 1 byte. The strips are encoded with the least significant bit on the top, shifting by one bit right as it scans vertically. The PRC can also invert the graphics as it renders them by setting the appropriate bit in PRC_MODE.
Maps can be offset up to 127 pixels vertically or horizontally (PRC_SCROLL_X and PRC_SCROLL_Y), and is clamped to the size of the map itself, writes to the scroll registers when the value is out of bounds does not update the location in which rendering begins, but the values of the registers themselves changes. Interestingly, these values are only verified when the register is written, and changing the tile map size will result in maps rendering gibberish tiles.
Under no circumstances do the maps wrap. To create smooth scrolling, the entire map must be rewritten to simulate wrap around.
Sprite Rendering Stage
After the map rendering stage, the Sprite Rendering stage takes effect. The PRC allows for 24 16x16 on screen sprites per frame, which can be positioned anywhere on screen.
Sprites are controlled by 24, 4 byte attribute blocks located between $1300 ~ $135F.
|0||Sprite X Position|
|1||Sprite Y Position|
|3||Enable||Invert Color||Vertical Flip||Horizontal Flip|
The Position operates on a virtual (128x128) screen, with is positioned at (-16,-16) on the frame buffer. This allows for sprites to be positioned partially off screen on all sides. The MSB of both coordinate elements are ignored, so it can wrap around if care is not taken.
Sprite Tiles are loaded using PRC_SPR_* as the base address, with sprites tiles being 64 bytes in length (making a full tile set 16kB).
Sprites are rendered by using 8 tiles, 4 mask and 4 graphic. The mask tiles use a set pixel to signify which bits are to be left alone and which bits are to be overwritten with the graphic bits. A set bit leaves a pixel unchanged. The tiles are formatted in the same way as the Map tiles.
The 8 tiles (in order) are: Mask (0,0) Mask (0,8) Graphic (0,0) Graphic (0,8) Mask (8,0) Mask (8,8) Graphic (8,0) Graphic (8,8)
Sprites are rendered in reverse order, so Sprite #0 would always been on top. This means internally sprite #23 is drawn first, followed by #22 up to #0 (painter's order)
Frame Copy Stage
To Be Written.
PRC Timing Information
To Be Written.